ASTM A860 PDF

ASTM A/AM Direct No.: + Fax No.: + Email: [email protected] Board No.: + ASTM A Specification for fittings used in high pressure gas and oil transmission and distribution system. Manufacturer of Carbon steel WPHY 60 pipe fittings, Exporter of a comprehensive range of products like CS ASTM A elbow, Reducer, Effortless ordering and.

Author: Voodoozilkree Nekora
Country: Lithuania
Language: English (Spanish)
Genre: History
Published (Last): 23 July 2018
Pages: 238
PDF File Size: 5.4 Mb
ePub File Size: 19.11 Mb
ISBN: 230-1-56025-711-2
Downloads: 27503
Price: Free* [*Free Regsitration Required]
Uploader: Kilkis

Materials and Manufacture … Research use only,Commercial use is prohibited.

Carbon steel WPHY 65 buttweld fittings, ASTM A WPHY GR 65 Pipe Fittings Manufacturer, Exporter.

In pallets, in plywood cases, in bulk. In addition, if requested to provide test reports, the manufacturer shall also provide the following, when applicable: Cvenergy absorptionC; measured at?

A chemical analysis shall a8600 performed on deposited weld metal for. BoxArlingate Ln.

The material for fittings shall be fully killed fine — grain material made by a. This abstract is a brief summary of the referenced standard.

Other imperfections shall be treated in accordance with The product analysis shall be the basis for rejection. In case of con? These fittings are for use in high — pressure gas and oil transmission and awtm system. Failure to comply with the general requirements of Speci? JIS G Steel pipes for low temperature service. What can I do for you? Permission rights to photocopy the standard may also be secured from the ASTM website www. One or more of the supplementary requirements may be specified in the order.

  JORGE MOREL MISIONERA PDF

In addition, quench and tempered? Starting materials shall consist of plate, sheet, forgings, forging quality bar, and seamless or fusion-welded tubular products with filler metal added.

A860 WPHY 60 PIPE FITTTINGS

Acceptable tees shall be marked with the symbol PT or MT, as applicable, to indicate compliance. These fittings are for use in high-pressure gas and oil transmission and distribution systems. Within the text, the SI units are shown in brackets. Fittings formed above the transformation temperature or upon which welding is performed, shall be cooled to below the lower critical temperature prior to heat treatment.

No cracks shall be permitted. Only the ultimate tensile strength need meet the minimum requirement of Table 2. The chemical composition thus determined shall conform to Table 1. JIS G Carbon steel pipes for high temperature service. These fittings are for use in high-pressure gas and oil transmission and distribution systems. Workmanship, Finish and Appearance This specification covers wrought high-strength low-alloy butt-welding steel fittings of seamless and electric fusion-welded construction for applications in high-pressure gas and oil transmission and distribution systems.

And over, Sizes tested Section;min. Small size specimens shall be used only when the material thickness does not permit full size specimens. Research use only,Commercial use is a680. The nickel content of the deposited weld metal.

ASTM A WPHY GR 60 Pipe Fittings, Carbon steel WPHY 60 buttweld fittings Manufacturer, Exporter.

Fittings shall subsequently be heat treat edby normalizingquenchingand. Weld-metal specimens shall be specimens with the axis transverse to the weld seam. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

  HOW TO READ AKASHIC RECORDS LINDA HOWE PDF

Combining values from the two systems may result in nonconformance with this specification. The impact specimens shall not be?

A860 WPHY 65 PIPE FITTTINGS

There sults shall conform to Table 1 for either. All values are Maximum unless A range is stated.

DIN Medium-weight threaded steel tubes. After the removal of any cracksthe tees shall be re. One or more of the supplementary requirements may be specified in the order.

Only the side wall area of the tees need be examined. Combining values from the two systems may result in non-conformance with the standard.

Notch Toughness Properties 8. The chemical composition thus determined.

The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. When the section thickness lies between two values de? All base metal specimens shall be removed with the axis of the specimens longitudinal to the direction of primary metal?